Electricity calculators / Unit conversions
Know your usage. Understand your bill.
Watt-Hour Runtime Calculator
A watt-hour rating becomes an estimated runtime only after specifying the load. A 500 Wh source with 80% usable energy and 90% delivery efficiency offers 360 Wh to the load, or 3.6 hours at 100 W. A changing load should use a defensible average output demand.
Your inputs
Your result
Awaiting your inputsEnter your values and press Calculate. Your result will appear here.
Clear units · Editable assumptions · Published formula sources
The method
Formula and calculation steps
Runtime hours = rated Wh×usable fraction×efficiency/load W.
Estimate operating hours from watt-hours, usable fraction, conversion efficiency and continuous watts.
- Identify the quantities and units required by the form.
- Use measurements, a current bill or relevant equipment data for the same period.
- Apply the displayed formula, then check the assumptions and related outputs.
This steady energy balance does not model battery voltage sag, manufacturer discharge curves, surge limits or temperature behavior.
Watt-hours to operating hours for an appliance or battery
A watt-hour rating becomes an estimated runtime only after specifying the load. A 500 Wh source with 80% usable energy and 90% delivery efficiency offers 360 Wh to the load, or 3.6 hours at 100 W. A changing load should use a defensible average output demand.
Use this for an early portable power, RV or appliance backup budget when the supplied assumptions are meaningful. It does not establish whether the device can support the load current or startup demand. If power is measured at the battery and already includes conversion losses, applying the same loss again would double-count it.
Continue with: Energy Unit Converter · Power Unit Converter · Battery Ah, mAh & Energy Calculator · kWh to Amp-Hours Calculator
Check the numbers
Watt-Hour Runtime Calculator: calculated examples
Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.
Worked example with the starting inputs
Rated energy: 500 Wh; Usable fraction: 80 %; Conversion efficiency: 90 %; Continuous output load: 100 W. Estimated runtime: 3.6 hours.
| Output | Computed value |
|---|---|
| Estimated runtime | 3.6 hours |
| Delivered usable energy | 360 Wh |
| Load | 100 W |
How the answer changes
| Scenario | Changed input | Result |
|---|---|---|
| 25 W | Continuous output load: 25 W | 14.4 hours |
| 50 W | Continuous output load: 50 W | 7.2 hours |
| 75 W | Continuous output load: 75 W | 4.8 hours |
| 100 W | Continuous output load: 100 W | 3.6 hours |
| 150 W | Continuous output load: 150 W | 2.4 hours |
| 200 W | Continuous output load: 200 W | 1.8 hours |
| 300 W | Continuous output load: 300 W | 1.2 hours |
All inputs not changed in a row use: Rated energy = 500 Wh; Usable fraction = 80 %; Conversion efficiency = 90 %; Continuous output load = 100 W. These are chosen examples, not current rates or product performance claims.
Common questions
Can I convert Wh to hours directly?
Only with a load in watts and any relevant usable-energy assumptions.
How long will 1,000 Wh run 100 W?
Ten hours in an ideal full-use lossless case. Real use may be shorter depending on the battery and equipment.
Should I enter appliance output or electrical input?
Use the electrical load presented to the source at the chosen measurement boundary, not a heat or motor-output rating.
Does runtime scale perfectly with battery size?
Only within this fixed model. Actual battery behavior and power limits may change.
Is this an NFPA 855 compliance calculator?
No. A basic energy balance does not verify an energy storage installation against NFPA or local requirements.
Which inputs should I verify before using this result?
Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.
Where do the formulas and example values come from?
The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.
Related calculators
Formula sources and references
These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.
- NIST SP 811, Appendix B: SI and non-SI conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors
- Virginia Cooperative Extension, publication 2901-9014: appliance energy estimationhttps://www.pubs.ext.vt.edu/2901/2901-9014/2901-9014.html