Electricity Costby Voltage Drop Calculator

Electricity calculators / Unit conversions

Know your usage. Understand your bill.

Battery Ah, mAh & Energy Calculator

Ah and mAh describe electric charge, while Wh and kWh describe energy. Voltage connects the two. A 100 Ah battery at 12 V has 1,200 Wh of nominal energy, but the same Ah at 48 V has four times that energy. Ah alone cannot establish electricity cost or operating time.

Your inputs

Ah
V

Example inputs are editable. Use your own equipment data and current tariff. Prices use one consistent currency: enter 20 cents or pence as 0.20.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Clear units · Editable assumptions · Published formula sources

The method

Formula and calculation steps

Wh = Ah×nominal V; kWh = Ah×V/1,000; mAh = Ah×1,000.

Convert battery charge capacity to nominal watt-hours and kilowatt-hours at an explicit voltage.

  1. Identify the quantities and units required by the form.
  2. Use measurements, a current bill or relevant equipment data for the same period.
  3. Apply the displayed formula, then check the assumptions and related outputs.

This is nominal energy, not guaranteed delivered energy or charger input. Use the pack voltage that matches the Ah rating.

Amp-hours, milliamp-hours and kilowatt-hours

Ah and mAh describe electric charge, while Wh and kWh describe energy. Voltage connects the two. A 100 Ah battery at 12 V has 1,200 Wh of nominal energy, but the same Ah at 48 V has four times that energy. Ah alone cannot establish electricity cost or operating time.

For a power bank or phone pack labeled in mAh, divide by 1,000 before entering Ah. Use the cell or pack nominal voltage corresponding to that label, not an unrelated USB charging voltage. Battery-bank series and parallel configuration determines which nominal voltage and Ah values belong together.

Check the numbers

Battery Ah, mAh & Energy Calculator: calculated examples

Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.

Worked example with the starting inputs

Charge capacity: 100 Ah; Nominal battery voltage: 12 V. Nominal stored energy: 1,200 Wh.

OutputComputed value
Nominal stored energy1,200 Wh
Nominal kilowatt-hours1.2 kWh
Charge capacity100,000 mAh

How the answer changes

ScenarioChanged inputResult
25 AhCharge capacity: 25 Ah300 Wh
50 AhCharge capacity: 50 Ah600 Wh
75 AhCharge capacity: 75 Ah900 Wh
100 AhCharge capacity: 100 Ah1,200 Wh
150 AhCharge capacity: 150 Ah1,800 Wh
200 AhCharge capacity: 200 Ah2,400 Wh
300 AhCharge capacity: 300 Ah3,600 Wh

All inputs not changed in a row use: Charge capacity = 100 Ah; Nominal battery voltage = 12 V. These are chosen examples, not current rates or product performance claims.

Common questions

How do I convert mAh to watt-hours?

Wh equals mAh times nominal volts divided by 1,000. Enter 10 for a 10,000 mAh rating in the Ah field.

What is 100 Ah in kWh?

At 12 V it is 1.2 nominal kWh; at 48 V it is 4.8 kWh. Voltage is required.

How do I calculate watt hours of a battery bank?

Use the complete bank nominal voltage and bank Ah. Do not multiply series Ah as though the batteries were in parallel.

Does this tell me usable capacity?

No. Discharge limits, losses, temperature and aging reduce deliverable energy. Use equipment data.

How do I convert 100 Wh to mAh?

Use the inverse energy-to-Ah calculator with the corresponding nominal voltage, then multiply Ah by 1,000.

Which inputs should I verify before using this result?

Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.

Where do the formulas and example values come from?

The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.

Formula sources and references

These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.

  • NIST SP 811, Appendix B: SI and non-SI conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors
  • US EIA: Measuring electricity; power and energy unitshttps://www.eia.gov/energyexplained/electricity/measuring-electricity.php