Electricity Costby Voltage Drop Calculator

Electricity calculators / Gas, carbon & business

Know your usage. Understand your bill.

kWh to Gas Volume Calculator

The inverse gas conversion divides energy by the energy per corrected cubic metre. It is useful for checking a gas energy statement or comparing two representations of the same gas amount. It is not appropriate to interpret an electric appliance’s kWh as gas volume without accounting for the different conversion efficiencies.

Your inputs

kWh
MJ/m³
×

Example inputs are editable. Use your own equipment data and current tariff. Prices use one consistent currency: enter 20 cents or pence as 0.20.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Clear units · Editable assumptions · Published formula sources

The method

Formula and calculation steps

Gas m³ = kWh×3.6/(calorific value×volume correction).

Convert gas energy into a corresponding billing volume using supplied calorific and correction factors.

  1. Identify the quantities and units required by the form.
  2. Use measurements, a current bill or relevant equipment data for the same period.
  3. Apply the displayed formula, then check the assumptions and related outputs.

There is no universal kWh-to-m³ factor. The result applies only to gas energy at the entered calorific basis, not electrical energy produced from that gas.

Energy-to-gas-volume conversion with matching assumptions

The inverse gas conversion divides energy by the energy per corrected cubic metre. It is useful for checking a gas energy statement or comparing two representations of the same gas amount. It is not appropriate to interpret an electric appliance’s kWh as gas volume without accounting for the different conversion efficiencies.

Use the exact factors from the same bill or supply specification when reversing a billing calculation. The cubic-foot outputs follow the rounded UK billing factors used in the forward tool. For engineering gas volume at another reference pressure or temperature, obtain an appropriate physical conversion rather than assuming the billing approximation applies.

Check the numbers

kWh to Gas Volume Calculator: calculated examples

Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.

Worked example with the starting inputs

Energy used: 300 kWh; Calorific value: 39.5 MJ/m³; Volume correction factor: 1.02264 ×. Corresponding gas volume: 26.736459 m³.

OutputComputed value
Corresponding gas volume26.736459 m³
UK billing cubic feet equivalent944.751192 ft³
UK billing hundreds of cubic feet9.447512 hundreds ft³

How the answer changes

ScenarioChanged inputResult
75 kWhEnergy used: 75 kWh6.684115 m³
150 kWhEnergy used: 150 kWh13.368229 m³
225 kWhEnergy used: 225 kWh20.052344 m³
300 kWhEnergy used: 300 kWh26.736459 m³
450 kWhEnergy used: 450 kWh40.104688 m³
600 kWhEnergy used: 600 kWh53.472917 m³
900 kWhEnergy used: 900 kWh80.209376 m³

All inputs not changed in a row use: Energy used = 300 kWh; Calorific value = 39.5 MJ/m³; Volume correction factor = 1.02264 ×. These are chosen examples, not current rates or product performance claims.

Common questions

Can 1 kWh always be converted to the same gas volume?

No. Gas composition and reference conditions affect calorific value and corrected volume.

Can I convert m³ of water using this?

No. Water heating needs mass, temperature rise and heating efficiency, not gas calorific value.

Does this estimate boiler gas use from heat demand?

Only if the entered kWh already represents purchased gas energy. Useful heat must first be divided by the boiler’s relevant efficiency.

Can I use the UK correction in Belgium?

Only if it matches the applicable bill. Defaults are examples of the cited UK approach.

What is the reverse formula?

Multiply kWh by 3.6 and divide by calorific value in MJ/m³ times the volume correction.

Which inputs should I verify before using this result?

Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.

Where do the formulas and example values come from?

The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.

Formula sources and references

These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.

  • UK Office for Product Safety and Standards: gas readings and bill calculationhttps://www.gov.uk/guidance/gas-meter-readings-and-bill-calculation
  • NIST SP 811, Appendix B: SI and non-SI conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors