Electricity Costby Voltage Drop Calculator

Electricity calculators / Gas, carbon & business

Know your usage. Understand your bill.

Electricity Load Factor Calculator

Load factor compares average power with the measured peak over a stated period. A fairly steady load has a higher ratio than a sharply peaking load with the same energy. It is not the motor shaft loading percentage or an electrical power factor.

Your inputs

kWh
h
kW

Example inputs are editable. Use your own equipment data and current tariff. Prices use one consistent currency: enter 20 cents or pence as 0.20.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Clear units · Editable assumptions · Published formula sources

The method

Formula and calculation steps

Load factor = period kWh/(peak kW×period hours)×100; average kW = kWh/period hours.

Calculate load factor from matching energy, measured peak demand and the full observation period.

  1. Identify the quantities and units required by the form.
  2. Use measurements, a current bill or relevant equipment data for the same period.
  3. Apply the displayed formula, then check the assumptions and related outputs.

A result above 100% signals inconsistent inputs under this definition. Energy and peak must use the same measurement boundary and period.

Average demand and the shape of electricity use

Load factor compares average power with the measured peak over a stated period. A fairly steady load has a higher ratio than a sharply peaking load with the same energy. It is not the motor shaft loading percentage or an electrical power factor.

The measurement period includes every elapsed hour, including weekends or shutdowns, when comparing against billing-period energy. If you instead want a production-hours utilization ratio, state that different boundary explicitly. Load factor summarizes a profile but cannot reconstruct its hourly values or determine what equipment caused the peak.

Check the numbers

Electricity Load Factor Calculator: calculated examples

Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.

Worked example with the starting inputs

Energy used: 300 kWh; Hours in measurement period: 720 h; Measured peak demand: 2 kW. Period load factor: 20.833333 %.

OutputComputed value
Period load factor20.833333 %
Average power0.416667 kW
Measured peak2 kW

How the answer changes

ScenarioChanged inputResult
75 kWhEnergy used: 75 kWh5.208333 %
150 kWhEnergy used: 150 kWh10.416667 %
225 kWhEnergy used: 225 kWh15.625 %
300 kWhEnergy used: 300 kWh20.833333 %
450 kWhEnergy used: 450 kWh31.25 %
600 kWhEnergy used: 600 kWh41.666667 %
900 kWhEnergy used: 900 kWh62.5 %

All inputs not changed in a row use: Energy used = 300 kWh; Hours in measurement period = 720 h; Measured peak demand = 2 kW. These are chosen examples, not current rates or product performance claims.

Common questions

How do I calculate average kW demand from kWh?

Divide energy by the number of elapsed hours. Peak demand must be measured separately.

Why is my load factor greater than 100%?

The supplied peak is below average power, which is inconsistent. Check units, dates and measurement scope.

Is load factor the same as power factor?

No. Load factor compares average and peak power over time. Power factor relates real and apparent AC power.

Should I enter business opening hours?

For a full billing-period load factor, use all hours in that period. Opening hours would define a different metric.

Does a higher factor guarantee a lower bill?

No. Tariff rates, absolute energy and billed demand still determine cost.

Which inputs should I verify before using this result?

Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.

Where do the formulas and example values come from?

The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.

Formula sources and references

These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.

  • US EIA: Measuring electricity; power and energy unitshttps://www.eia.gov/energyexplained/electricity/measuring-electricity.php
  • NIST SP 811, Appendix B: SI and non-SI conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors