Electricity calculators / Appliances & equipment
Know your usage. Understand your bill.
Water Heating Energy Cost Calculator
Heating a quantity of water requires energy proportional to its mass and temperature rise. This simplified calculation treats one litre as approximately one kilogram and uses a constant specific heat near ordinary liquid-water conditions. It is appropriate for a stated sensible temperature rise, not for evaporation, freezing or boiling calculations.
Your inputs
Your result
Awaiting your inputsEnter your values and press Calculate. Your result will appear here.
Clear units · Editable assumptions · Published formula sources
The method
Formula and calculation steps
Heat kWh ≈ litres×4,186×temperature rise/3,600,000; electrical kWh = heat/efficiency; hours = electrical kWh×1,000/input W.
Estimate sensible water heating energy, electricity cost and heating time for a stated temperature rise.
- Identify the quantities and units required by the form.
- Use measurements, a current bill or relevant equipment data for the same period.
- Apply the displayed formula, then check the assumptions and related outputs.
Assumes liquid water at approximately 1 kg/L and specific heat 4,186 J/(kg·°C), without boiling or phase change. Tank and pipe losses are represented only through your chosen efficiency.
How much electricity is needed to heat water?
Heating a quantity of water requires energy proportional to its mass and temperature rise. This simplified calculation treats one litre as approximately one kilogram and uses a constant specific heat near ordinary liquid-water conditions. It is appropriate for a stated sensible temperature rise, not for evaporation, freezing or boiling calculations.
The required heat and purchased electrical energy are different if losses are present. Heating time also needs the actual electrical input power. A tank heater may cycle, and surrounding losses can change during a long heating period; the constant-efficiency result is a planning approximation. A heat-pump water heater needs an appropriate COP model rather than an efficiency restricted to 100 percent.
Continue with: Appliance Running Cost Calculator · Home Electricity Usage Calculator · PC & Server Electricity Cost Calculator · Air Conditioner Electricity Cost Calculator
Check the numbers
Water Heating Energy Cost Calculator: calculated examples
Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.
Worked example with the starting inputs
Water volume: 100 L; Initial water temperature: 15 °C; Target water temperature: 60 °C; Input-to-water efficiency: 90 %; Continuous heater input: 3,000 W; Electricity unit rate: 0.2 currency/kWh. Electrical heating energy: 5.813889 kWh.
| Output | Computed value |
|---|---|
| Electrical heating energy | 5.813889 kWh |
| Useful heat added | 5.2325 kWh thermal |
| Electricity cost | 1.162778 currency |
| Constant-input heating time | 1.937963 hours |
How the answer changes
| Scenario | Changed input | Result |
|---|---|---|
| 25 L | Water volume: 25 L | 1.453472 kWh |
| 50 L | Water volume: 50 L | 2.906944 kWh |
| 75 L | Water volume: 75 L | 4.360417 kWh |
| 100 L | Water volume: 100 L | 5.813889 kWh |
| 150 L | Water volume: 150 L | 8.720833 kWh |
| 200 L | Water volume: 200 L | 11.627778 kWh |
| 300 L | Water volume: 300 L | 17.441667 kWh |
All inputs not changed in a row use: Water volume = 100 L; Initial water temperature = 15 °C; Target water temperature = 60 °C; Input-to-water efficiency = 90 %; Continuous heater input = 3,000 W; Electricity unit rate = 0.2 currency/kWh. These are chosen examples, not current rates or product performance claims.
Common questions
How many watts are needed to heat water?
Watts determine the heating rate, while the water amount and temperature rise determine required energy. This page estimates time for an entered constant heater input.
Can I convert cubic metres of water to kWh?
Not without a temperature rise and thermal model. Convert cubic metres to litres by multiplying by 1,000, then enter the liquid-water heating conditions.
What energy heats 100 litres from 15°C to 60°C?
Using the stated approximations, useful heat is 5.2325 kWh. At 90% efficiency, purchased electricity is about 5.813889 kWh.
Does this include boiling or steam?
No. Latent heat and phase changes are outside this sensible-heating model. Temperatures here stay below 100°C.
Can I use it to size an instant water heater?
Not as a complete design. Continuous flow, supply temperature, installation requirements and electrical capacity need separate calculations.
Which inputs should I verify before using this result?
Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.
Where do the formulas and example values come from?
The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.
Related calculators
Formula sources and references
These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.
- OpenStax College Physics 2e, section 14.2: Q = mcΔT and water heat capacityhttps://openstax.org/books/college-physics-2e/pages/14-2-temperature-change-and-heat-capacity
- NIST SP 811, Appendix B: SI and non-SI conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors