Electricity calculators / Appliances & equipment
Know your usage. Understand your bill.
Air Conditioner Electricity Cost Calculator
An air conditioner power consumption calculation needs electrical input rather than cooling output. A cooling rating of 12,000 BTU/h describes heat removed, not energy purchased from the electricity meter. The compressor, fans and controls contribute to wall input. For an inverter unit, the label maximum is especially unlikely to equal every hour’s average.
Your inputs
Your result
Awaiting your inputsEnter your values and press Calculate. Your result will appear here.
Clear units · Editable assumptions · Published formula sources
The method
Formula and calculation steps
Average enabled W = runningW×duty/100 + idleW×(1−duty/100); kWh = averageW×hours×days/1,000.
Estimate aircon or cycling equipment consumption from electrical input, enabled hours and an explicit running fraction.
- Identify the quantities and units required by the form.
- Use measurements, a current bill or relevant equipment data for the same period.
- Apply the displayed formula, then check the assumptions and related outputs.
Cooling BTU/h, refrigeration tons and motor horsepower are not input watts. Inverter/VRF systems vary continuously, so use a measured average when available.
AC power consumption, compressor cycling and inverter aircon
An air conditioner power consumption calculation needs electrical input rather than cooling output. A cooling rating of 12,000 BTU/h describes heat removed, not energy purchased from the electricity meter. The compressor, fans and controls contribute to wall input. For an inverter unit, the label maximum is especially unlikely to equal every hour’s average.
The running fraction is a scenario assumption, not a thermostat forecast. Weather, insulation, solar gain and setpoint affect the real duty. This simplified two-state model can also estimate a chiller, boiler auxiliary or thermostat-controlled load when the two electrical states are known, but it does not simulate a building or infer VRF part-load efficiency.
Continue with: Appliance Running Cost Calculator · Home Electricity Usage Calculator · PC & Server Electricity Cost Calculator · Refrigerator Energy Cost Calculator
Check the numbers
Air Conditioner Electricity Cost Calculator: calculated examples
Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.
Worked example with the starting inputs
Electrical input while running: 1,200 W; Input while not cooling: 10 W; Running fraction of enabled time: 60 %; Enabled hours per day: 8 h/day; Days in period: 30 days; Electricity unit rate: 0.2 currency/kWh. Cycling-load energy cost: 34.752 currency.
| Output | Computed value |
|---|---|
| Cycling-load energy cost | 34.752 currency |
| Average enabled input | 724 W |
| Period electricity | 173.76 kWh |
| Daily electricity | 5.792 kWh/day |
How the answer changes
| Scenario | Changed input | Result |
|---|---|---|
| 15 % | Running fraction of enabled time: 15 % | 9.048 currency |
| 30 % | Running fraction of enabled time: 30 % | 17.616 currency |
| 45 % | Running fraction of enabled time: 45 % | 26.184 currency |
| 60 % | Running fraction of enabled time: 60 % | 34.752 currency |
| 90 % | Running fraction of enabled time: 90 % | 51.888 currency |
| 100 % | Running fraction of enabled time: 100 % | 57.6 currency |
All inputs not changed in a row use: Electrical input while running = 1,200 W; Input while not cooling = 10 W; Running fraction of enabled time = 60 %; Enabled hours per day = 8 h/day; Days in period = 30 days; Electricity unit rate = 0.2 currency/kWh. These are chosen examples, not current rates or product performance claims.
Common questions
How do I calculate power consumption of AC per day?
Average the electrical input over the enabled schedule, then multiply by hours and divide by 1,000. Use actual input watts rather than cooling capacity.
Can I convert one ton of cooling directly to input watts?
No. Cooling capacity is thermal output. Electrical input also depends on efficiency and operating conditions.
What duty cycle should I use?
Use measured compressor on-time or a clearly identified scenario. The illustrative default is not an appliance-specific value.
Is 100% duty the worst possible input?
It means the entered running watts apply through all enabled hours. A different power state or startup condition can still exceed that entered value.
Does this model inverter AC or VRF accurately?
Only as an equivalent average or simplified two-state estimate. It does not implement a manufacturer performance map.
Which inputs should I verify before using this result?
Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.
Where do the formulas and example values come from?
The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.
Related calculators
Formula sources and references
These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.
- Virginia Cooperative Extension, publication 2901-9014: appliance energy estimationhttps://www.pubs.ext.vt.edu/2901/2901-9014/2901-9014.html
- US EIA: Measuring electricity; power and energy unitshttps://www.eia.gov/energyexplained/electricity/measuring-electricity.php