Electricity Costby Voltage Drop Calculator

Electricity calculators / Appliances & equipment

Know your usage. Understand your bill.

Generator Load & Energy Cost Calculator

A generator wattage calculator must distinguish continuous running power from an additional starting demand. Enter the largest credible simultaneous starting event as extra power above the already-counted running total. Entering the entire starting load again would double-count its running component. The margin is a user-selected planning allowance, not a code requirement.

Your inputs

W
W
%
h
fuel units/h
currency/fuel unit

Example inputs are editable. Use your own equipment data and current tariff. Prices use one consistent currency: enter 20 cents or pence as 0.20.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Clear units · Editable assumptions · Published formula sources

The method

Formula and calculation steps

Planning peak W = (running W + additional starting W)×(1+margin/100); energy kWh = running W×hours/1,000.

Check an entered generator load scenario and fuel-only electricity cost from a measured fuel rate.

  1. Identify the quantities and units required by the form.
  2. Use measurements, a current bill or relevant equipment data for the same period.
  3. Apply the displayed formula, then check the assumptions and related outputs.

This does not select a generator or model fuel consumption. Starting power factor, transient response, altitude, waveform and manufacturer ratings need separate checking.

Home, portable and RV generator running versus starting watts

A generator wattage calculator must distinguish continuous running power from an additional starting demand. Enter the largest credible simultaneous starting event as extra power above the already-counted running total. Entering the entire starting load again would double-count its running component. The margin is a user-selected planning allowance, not a code requirement.

A diesel generator cost per kWh calculation also needs fuel consumption at the actual load. Rated kW and fuel tank size alone do not establish that rate. The fuel-only result excludes maintenance, ownership, transport and idle operation; it should not be compared with a full utility bill without consistent cost boundaries.

Check the numbers

Generator Load & Energy Cost Calculator: calculated examples

Compare stated scenarios rather than an unexplained rule of thumb. Each row uses the same calculation function as the form.

Worked example with the starting inputs

Simultaneous running load: 3,000 W; Extra starting load above running total: 2,000 W; Chosen capacity margin: 20 %; Operating duration: 5 h; Measured fuel consumption at this load: 1.5 fuel units/h; Fuel price: 1.4 currency/fuel unit. Scenario peak with chosen margin: 6,000 W.

OutputComputed value
Scenario peak with chosen margin6,000 W
Running energy15 kWh
Fuel-only period cost10.5 currency
Fuel-only cost per kWh0.7 currency/kWh

How the answer changes

ScenarioChanged inputResult
750 WSimultaneous running load: 750 W3,300 W
1,500 WSimultaneous running load: 1,500 W4,200 W
2,250 WSimultaneous running load: 2,250 W5,100 W
3,000 WSimultaneous running load: 3,000 W6,000 W
4,500 WSimultaneous running load: 4,500 W7,800 W
6,000 WSimultaneous running load: 6,000 W9,600 W
9,000 WSimultaneous running load: 9,000 W13,200 W

All inputs not changed in a row use: Simultaneous running load = 3,000 W; Extra starting load above running total = 2,000 W; Chosen capacity margin = 20 %; Operating duration = 5 h; Measured fuel consumption at this load = 1.5 fuel units/h; Fuel price = 1.4 currency/fuel unit. These are chosen examples, not current rates or product performance claims.

Common questions

Can I add all starting watts together?

Only if the loads genuinely start simultaneously. Use a credible worst event and the manufacturer’s startup information.

Is this a generator recommendation?

No. It reports the scenario you enter. Verify continuous and surge ratings, voltage, phase and load compatibility against the exact equipment documentation.

How do I calculate diesel generator electricity cost?

Divide measured fuel cost per hour by actual electrical kW output at that same operating point. This form performs that fuel-only calculation.

Does the margin come from an electrical standard?

No. It is explicitly your planning assumption, not a prescribed design factor.

Can I use propane instead of diesel?

Yes, if consumption and unit price use the same fuel unit. Fuel performance is entered, not inferred.

Which inputs should I verify before using this result?

Check the units, dates and measurement boundary shown above. The examples are deliberately chosen scenarios rather than current tariffs, certified product ratings or promises about a particular installation.

Where do the formulas and example values come from?

The method is explained on this page and the published references are listed below as plain-text addresses. Example inputs are illustrative; comparison rows are computed with the same calculation function as the form.

Formula sources and references

These references support the units and underlying methods. Defaults and comparison cases are illustrative inputs, not current tariffs or product test data.

  • Virginia Cooperative Extension, publication 2901-9014: appliance energy estimationhttps://www.pubs.ext.vt.edu/2901/2901-9014/2901-9014.html
  • US EIA: Measuring electricity; power and energy unitshttps://www.eia.gov/energyexplained/electricity/measuring-electricity.php